Views: 2 Author: Site Editor Publish Time: 2020-10-17 Origin: Site
You just bought your new gun cleaning kit, so now what? The first thing you’re going to want to do if you’re new is to watch a few YouTube videos and read the instructions.
Each gun is a bit different when it comes to cleaning, so you want to read and re-read the owner’s manual for your particular gun.
We’ll go over the basics of using a universal gun cleaning kit if you own a rifle, handgun or shotgun this is what you’ll want to use.
AR’s can be a little different to clean and usually require special tools such as an AR cleaning tool.
One time I bought a new M4 and didn’t clean it before taking it to the range. Wiped off the grease on the exterior and after about 50 rounds I had a brass over bolt failure…
Almost all new guns come with a bunch of grease and sticky solvent on them. This is to make sure they don’t rust while sitting on the shelf for months or years.
This lubricant they put on it is not a shooting lubricant, so you want to remove it and clean your new gun as well as possible.
You should always do this because you don’t know how it works until you take it apart.
You should ALWAYS inspect a new gun before firing it, looking for worn components, broken or little pieces of sawdust and what not in the gun.
I got issued a brand new, out of the package M4 right before shooting the range and skipped cleaning, just wiped the crap off the outside. Had a brass over bolt failure on round 76.
Be sure to wash your hand before doing anything. This will help prevent oils from getting onto the outer and inner parts of your gun. Most people, including myself, wear gloves when cleaning their guns to prevent oil absorbing into the skin.
If you’re cleaning your guns for years, then the risk of getting some of these solvent into your skin will not be very good for. The disposable black nitrile gloves are my personal favorite and a favorite among many.
Make sure the ammo is out of reach. There is a possibility that you could accidentally discharge your gun while cleaning it, if it were loaded. There’s also a small chance that you could shoot a box of ammo, so double and triple check this step.
If you have a gun cleaning mat, this is the time to use it. I would highly recommend using something to protect your surfaces from solvents and scratches.
To save time you can use a bore snake before using your cleaning rods. This will remove some of the gunk and only takes about 10 seconds. Using a bore snake will save you quite bit of time.
Read your manual and take apart everything accordingly. If you don’t have an owner’s manual you can usually find this on their website or even better find a YouTube video and follow along.
If you have a gun cleaning vise then you’ll want to secure it properly. A gun vise is amazing for keeping your gun steady and works amazingly well for long guns.
Not really necessary for handguns.
Make sure to PULL the brush through about 5-10 times. Be sure to pull only and don’t push.
Running the bore brush only in the same direction the bullet travels will prolong the life of the barrel.
The goal is to have the cleaning patches come out white. You can use 10-20 cleaning patches until this happens and they’re cheap so don’t worry.
If you pull out your cleaning patches and they’re black then you need to run your brushes through your gun again.
To do this you should use dry cleaning patches and gun mop attachment. After the cleaning solvent is all out you’re going to want to apply some lubricant.
Hoppe’s makes a good gun lubricant that you should apply after you’re done cleaning. What this does is protect from dust accumulating on your gun, which will leak to gunk buildup.
You can use the double-sided wire toothbrush for this task. Simply put a little bit of CLP on the brush and scrape off any areas that need to be cleaned.
You want to be a little bit of lubricant around the mechanics. Also look for any small rust area. Often times rust will start out as a little tiny speck and if you don’t spot it right away it can easily spread.
After washing your hands again, you should rub a little oil on them and this will remove any fingerprints that may have gotten on your gun while cleaning it.
Now you’re just about finished. You want to make sure your hands are oiled up with your lubricant and put all the pieces back.
This is the process to follow for MOST firearms. Each gun cleaning kit has different components but most of them have the same type of brushes and rods.
If you’re unsure how often to clean your firearm, it really depends on how often you use it and the type of ammo you’re using.